View LHIR9553_4537181.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only SURFACE MOUNT LED TAPE AND REEL
Pb
Lead-Free Parts
LHIR9553
DATA SHEET
DOC. NO REV DATE :
:
QW0905-L HIR9553 A
: 16 - Mar. - 2009
DCC
LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
PART NO. LHIR9553 Page 1/8
Package Dimensions
3.5 3.2 1.85
2.8
2.2
1.85 0.95 0.9 + 0.9 -
Note : 1.All dimension are in millimeter tolerance is O 0.2mm unless otherwise noted. 2.Specifications are subject to change without notice.
Directivity Radiation
0X -30X 30X
-60X
60X
100% 75% 50%
25%
0
25% 50% 75% 100%
LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
PART NO. LHIR9553 Page 2/8
Absolute Maximum Ratings at Ta=25 J
Ratings Parameter Symbol HIR Forward Current Peak Forward Current (300PPS,10g s Pulse) Power Dissipation Reverse Voltagev Operating Temperature Storage Temperature IF IFP PD Vr Topr Tstg 50 1 100 5 -55 ~ +100 -55 ~ +100 mA A mW V UNIT
J J
Electrical Optical Characteristics (Aa=25J )
PARAMETER Radiant Intensity Aperture Radiant Incidence Peak Emission Wavelength Spectral Line Half Width Forward Voltage Reverse Current Viewing Angle SYMBOL Le Ee
Min. 1.1 0.15
Typ. 1.9 0.27 850 50
Max.
UNIT mW/sr mW/cm nm nm
2
TEST CONDITION IF=20mA IF=20mA IF=20mA IF=20mA IF=20mA VR=5V
f peak f
VF IR 2c 1/2
1.2
1.6 100 120
V
g A
deg
Note : 1.The forward voltage data did not including O 0.1V testing tolerance. 2. The radiant intensity data did not including O 15% testing tolerance.
LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
PART NO. LHIR9553 2.Handling Precaution Page 3/8
1 Do not poke the silicone encapsulant with sharp objec t
2 Hold the LED only by the body
3 Do not atach assembied PCB
4 Do not touch the silicone encapsulant
5 Clean the silicone surface whit cotton bud with minimal pressure
6 Use pick and place nozzle per recommendation in datasheet
LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
PART NO. LHIR9553 Page 4/8
Typical Electro-Optical Characteristics Curve
HIR CHIP Fig.1 Forward Current vs. Rorward Voltage
1000
Fig.2 Relative Radiant Power vs. Wavelength
1.0
100 10 1 0.1 0.0
Relative Radiant Power Normalize @20mA
Forward Current[mA]
0.5
1.0
2.0
3.0
4.0
0.0 800
850
900
950
Forward Voltage[V]
Wavelength[nm]
Fig.3 Relative Radiant Power vs. Forward DC Current
10.0
Fig.4 Relative Radiant Power vs. Forward Peak Current
10.0
Relative Radiant Power Normalize @20mA
1.0
Relative Radiant Power Normalize @100 mA
1 10 100
1.0
0.1
0.1 10
100
1000
IFDC[mA]
IFPK[mA]
Fig.5 Forward DC Voltage vs. Temperature
1.2
Fig.6 Relative Radiant Power vs. Temperature
3.0
Forward DC Voltage Normalize @20mA, 25 J
Relative Radiant Power Normalize @ 20mA, 25J
1.1
2.5 2.0 1.5 1.0 0.5 0.0 -40
1.0
0.9
0.8 -40
-20
0
20
40
60
80
100
-20
0
20
40
60
80
100
Ambient Temperature[J]
Ambient Temperature[ J ]
LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
PART NO. LHIR9553 Recommended Soldering Conditions 1. Hand Solder
Basic spec is O 280J 3 sec one time only.
Page 5/8
2. Wave Solder
Soldering heat Max. 260J 245O 5J within 5 sec 120 ~ 150J Preheat
120 ~ 180 sec
3. LEAD Reflow Solder
Temp. (J ) 240
Rising +5J /sec Cooling -5J /sec
150 120
Preheat
60 ~ 120 sec
5sec
Time
4. PB-Free Reflow Solder
1~5 C/sec 260 C MaX. 10sec.Max
Preheat 180~200 C 1~5 C/sec
Above 220 C 60 sec.Max.
120 sec.Max.
Note: 1.Wave solder and reflow soldering should not be made more than one time. 2.You can just only select one of the soldering conditions as above.
LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
PART NO. LHIR9553 Precautions For Use: Storage time:
1.The operation of Temperatures and RH are : 5 J ~35J ,RH<60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than one week in an atmosphere 5 J ~ 35J ,RH<60%, they should be treated at 60JO 5 J fo r 15hrs.
Page 6/8
Drive Method:
LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40 % of its desired value.
Circuit model A LED
Circuit model B LED
(A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED.
Cleaning:
Use alcohol-based cleaning solvents such as isopropyl alcohol to clean the LED.
ESD(Electrostatic Discharge):
Static Electricity or power surge will damage the LED. Use of a conductive wrist band or anti-electrosatic glove is recommended when handing these LED. All devices, equipment and machinery must be properly grounded.
LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
PART NO. LHIR9553 Precautions For Use: Storage time:
1.The operation of Temperatures and RH are : O 30J ,RH<60%. 2.Once the package is opened, the products should be used within a week. Otherwise, they should be kept in a damp proof box with descanting agent. Considering the tape life, we suggest our customers to use our products within a year(from production date). 3.If opened more than168hrs in an atmosphere O 30J ,RH<60%, The single LED end product must use for 125 J for 10hours to eliminate wet 4.If opened more than168hrs in an atmosphere O 30J ,RH<60%, J The reel and carrier end product must use for 60 J for 24 hours to eliminate wet
Page 7/8
Drive Method:
LED is a current operated device, and therefore, requirer some kind of current limiting incorporated into the driver circuit. This current limiting typically takes the form of a current limiting resistor placed in series with the LED. Consider worst case voltage variations than could occur across the current limiting resistor. The forwrd current should not be allowed to change by more than 40 % of its desired value. Circuit model A LED Circuit model B LED
(A) Recommended circuit. (B) The difference of brightness between LED could be found due to the VF-IF characteristics of LED.
CAUTION
LEVEL
This bag contains MOISTURE-SENS DEVICES ITIVE 1.Shelf life in sealed bag:12months at O 30J and<60 (c) relative humidity(RH)eComplete package before open the packing f 2.Once the package is o pened,devices that will be subjected to infrared reflow must be (a)Mounted within 168 hours at factory conditions of30J/60MRH O (b)Stored at 30J/O10MRH within 168 hours O (c)The aluminum foil bag does out the vacuum ]d^From SMT to the IR timing control is 24 hours 12 3.If the humidity indicator 10 %RH is pink or af ter open package hrs house,the led monomer should be treated at125JO5Jfor10hrs. 4.The reel and carrier end product must use for 60 for 24 hours to J 5.eliminate wet I PC JED J- STD 033 / EC For the detail,please refer to the standard
3
LIGITEK ELECTRONICS CO.,LTD. Property of Ligitek Only
PART NO. LHIR9553 Reliability Test: Page 8/8
Classification
Test Item
Test Condition
1.Ta=Under Room Temperature As Per Data Sheet Maximum Rating. 2.If=20mA 3.t=1000 hrs (-24hrs, +72hrs)
Reference Standard
MIL-STD-750D: 1026 MIL-STD-883D: 1005 JIS C 7021: B-1
Operating Life Test
High Temperature Storage Test Endurance Test Low Temperature Storage Test
1.Ta=105 JO 5J 2.t=1000 hrs (-24hrs, +72hrs)
MIL-STD-883D:1008 JIS C 7021: B-10
1.Ta=-40 JO 5J 2.t=1000 hrs (-24hrs, +72hrs)
JIS C 7021: B-12
High Temperature High Humidity Storage Test
1.IR-Reflow In-Board, 2 Times 2.Ta=65JO 5J 3.RH=90 %~95 % 4.t=1000hrs O 2hrs 1.IR-Reflow In-Board,2 times 2.Ta=105 JO 5J & -40JO 5J (10min) (10min) 3.total 10 cycles
MIL-STD-202F:103B JIS C 7021: B-11
Thermal Shock Test
MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1011
Solder Resistance Test
1.T.Sol=260 JO 5J 2.Dwell Time= 10 O 1sec. 1.T.Sol=235 JO 5J 2.Immersion time 2 O 0.5sec 3.Immersion rate 25 O 2.5mm/sec 4.Immersion rate 25 O 2.5mm/sec 5.Coverage U 95% of the dipped surface 1.105J ~ 25J ~ 55J ~ 25J 30mins 5mins 30mins 5mins 2.10 Cyeles
MIL-STD-202F: 210A MIL-STD-750D: 2031 JIS C 7021: A-1 MIL-STD-202F: 208D MIL-STD-750D: 2026 MIL-STD-883D: 2003 IEC 68 Part 2-20 JIS C 7021: A-2 MIL-STD-202F: 107D MIL-STD-750D: 1051 MIL-STD-883D: 1010 JIS C 7021: A-4
Solderability Test Environmental Test Temperature Cycling
Solderability Test
Ramp-up rate(183 J to Peak) +3 J second max Temp. maintain at 125( O 25)J 120 seconds max Temp. maintain above 183 J 60-150 seconds Peak temperature range 235 J +5-0J Time within 5 J of actual Peak Temperature(tp) 10-30 seconds Ramp-down rate +6 J /second max
MIL-STD-750D:2031.2 J-STD-020

▲Up To Search▲

Price & Availability of LHIR9553

	To Download LHIR9553 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .